DU850SWKB0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pump impeller went crooked, apparently both from wear and moving the unit. Would not then stay in place.
Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Althea from Vancouver, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Wiggins, MS
- Parts Used:
- WPW10204131
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken trolley axle in rack adjuster
No tools required except possibly a small screwdriver to help remove stop in end of rack; part easily installed by hand and stop re-inserted. Finished in several minutes. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce W from WESTERLY, RI
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost the cap to the Rinse aid container in door
Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Union Bridge, MD
- Parts Used:
- WP8268645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheel on lower rack broke.
New one snapped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CLEVELAND, OH
- Parts Used:
- WP8066018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Soap door wouldn't open.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Enderlin, ND
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking around door
After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from PALATINE, IL
- Parts Used:
- WPW10204131
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
P piece of the adjuster rack was deteriorated and broke off
Crazy Glued it together until we received the new part, but it fell off again. My husband installed the new piece and said it only took him about 2 minutes. You just take off the end cap and pop in the new piece and adjust to match the one on the other side of the rack. He said it was extremely easy and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from EAST WINDSOR, NJ
- Parts Used:
- WP8268645
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel assembly was cracked
I just snapped the old one off and snapped the new one on..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from TEMECULA, CA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
NEW GASKET
I USED A PLUMBER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donal from SPRINGVILLE, TN
- Parts Used:
- 4318050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
One door spring broken, replaced both
As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from ORANGE, CA
- Parts Used:
- WP3379375
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
I took it too far apart
I had done a door on another brand a while back and thought it would be the same, WRONG. All I needed to do was 6 screws in the lower panels. It should have not taken me longer than 30 minutes.
2 screws in the floor panel, 2 screws in the lower L shaped panel, 2 screws in the bottom of the front panel to be replaced.
EASY
2 screws in the floor panel, 2 screws in the lower L shaped panel, 2 screws in the bottom of the front panel to be replaced.
EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Mount Pleasant, SC
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water leak from the pump housing.
I removed the three screws holding the motor on the housing. Then I took the two hoses off and from inside the washer I unscrewed the ring at the base of the wand that holds the housing in place and removed it. I then replaced the impeller and seals and reversed the process to put it back together. Cost me 26.00 for parts and shipping. I couldnt imagine what anyone else would have charged. I will do business with PartsSelect again in the future.
Was this instruction helpful to you?
Thank you for voting!