DU1100XTPQ0 Whirlpool Dishwasher - Instructions

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!

I read online about a few other people who had the blinking light problem. Suggestions were to press a series of other buttons in sequence. Didn't work. I went to the advice website and paid $24 to be told it was the control board. I ordered a control board. As I was preparing to install it, I noticed a black spot on the ribbon connector that was across two of the printed (?) flat wires. I gently scraped it off. It was shorting the two flat wires. I put it all back together with the old board, and all is working well. It's been a week.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Sorry -- but my 5 yearold replaced this broken item -- He helped by slipping off the old broken one and sliding in the new one -- No tools were necessary -- after all it was the silverware basket ...

put new hose on, very easy.

easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Pulled out the screws to the panel. Did a visual inspection and noticed a burn mark on a terminal on the circuit board. Replaced the board and now had no lights. Made sure the breaker wasn't tripped and than followed power through the dishwasher and it went to the fuse on the circuit board that you have to take from the old board and put it on the new board. Well anyway, the fuse was blown and had to get one of them. Now dishwasher works.

Took out the screws--found out what the problem was--ordered part (your people were helpfull--good customer people--received the part within the time I was told--installed according to the instructions--turned it on. . Working fine and guess what--I don't have to do the dishes anymore.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Removed old part and replaced with new part

first things first. troubleshoot.... unit wont run. no l.e.d.s at all. Opened front panel and first thing I see is a thermal cutout mounted outside of printed circuit board. After using a multimeter to check for continuity, used a set of alligator clips with a common lead, thus bypassing thermal cutout. Viola, she worked. Ordered part after finding site with google search. Part was delivered in two days.