DU8900XT3 Whirlpool Dishwasher - Instructions

real easy to install. i took off all 4 sets of rollers. i installed the first set improperly and the 2nd,3rd and 4th properly. i then went back and refasten the first one. no tools needed. 15 min.

Assemblies snap on, no tools needed

easy - removed old wheel holders & pushed new

ones in place. parts came in two days !!!!

Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.

Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Remove completely the old one and installed the new entire kit.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

Turned off electric to machine.Removed water with shop vac, Removed lower panel, removed drain hose from check valve and garbage disposal. using shop vac removed blockage from drain hose. Reconnected hose turned on electric cycled dishwasher. Didn't work. Turned off electric, removed water, removed basket, sprayer arm, pump cover, used a six point deep socket to hold impeller while removing 1/4 in. screw. Removed the impeller and found the problem.The lower impeller shaft is broke. removed separator, chopper blade and spring, removed pump cover and broken drain impeller and lower seal. Cleaned all old parts and installed new drain pump kit. Replaced spray arm , basket . Turned electric on, cycled the machine one time. Checked for leaks, replaced lower panels. Put away tools. Your video was very helpful. Your service was great. I received the parts the next day after ordering them. thank you. thank you.

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

Watched your video

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

The video was great! I couldn't have done it without it. The repair took me a little longer than expected because I did not have the right tools (torx head screwdriver), but once I went out and bought it, the rest was fairly easy. The old impeller had some build-up on it, so it was pretty hard taking it off the motor shaft: this was one of the hardest parts, since I was afraid of forcing it out and breaking something. Once I cleaned up the motor shaft, however, the new impeller went in easily. Both the old impeller and washer seal were damaged. Overall, I was very happy with Partselect's fast shipping, easy-to-use website and incredibly helpful installation videos. The machine is now not only NOT leaking anymore, but dishes are coming out MUCH cleaner. The dishwasher is over ten years old, so I was happy that this low-cost fix made such a big difference and we didn't have to buy a whole new dishwasher.