DU1048XTPS3 Whirlpool Dishwasher - Instructions

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

put new hose on, very easy.

Sorry -- but my 5 yearold replaced this broken item -- He helped by slipping off the old broken one and sliding in the new one -- No tools were necessary -- after all it was the silverware basket ...

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!

Pulled out the screws to the panel. Did a visual inspection and noticed a burn mark on a terminal on the circuit board. Replaced the board and now had no lights. Made sure the breaker wasn't tripped and than followed power through the dishwasher and it went to the fuse on the circuit board that you have to take from the old board and put it on the new board. Well anyway, the fuse was blown and had to get one of them. Now dishwasher works.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

Removed old part and replaced with new part

After researching the issue, it pointed to either a clogged hose or a bad pump. I cleaning the hose, verifying that there was no clog by using baking soda, vinegar and water. It would work, once maybe twice, then the water would sit again. I checked the line again, no issues. I purchased a new pump. The installation of the pump was easy, only to discover that this did NOT solve my problem. I am now considering a new dishwasher or purchasing a new $150 motor. It sucks not being able to send the parts back.

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on