GU2200XTSB2 Whirlpool Dishwasher - Instructions

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Remove front door panel, replace B-metal fuse.

Replace motor/pump assembly

Shut off circut breaker. . . Removed 6 screws. . . Lifted cover over control board. . . Removed old control board. . Installed new board. . Replaced cover and the 6 screws. . Turned on circut breaker. . . Turned washer on. . . . It worked. Thank you for the quick delivery!

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Just had to transfer all the kit parts from the old rack to the new one.
It was important to leave one side of the kit parts(the wheel and other plastic pieces) on the old one while transferring the other side of the kit parts to the new rack so that I had a visual reference for placement and orientation of the parts on the new rack.

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.