DU9400XT4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from Dayton, TX
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishrack Tines were breaking off due to age
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from VALLEJO, CA
- Parts Used:
- WP304204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing Spray Arm Broken
Snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Palm Springs, CA
- Parts Used:
- WP300845
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part
I just installed the new part. There were no tools required. I bought an extra part
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jupiter, FL
- Parts Used:
- 675544
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drain hose cracked. Leaked and warped wood floor.
Checked fill line. No leak. Checked drain hose, found crack in hose. Ordered the part, replaced.
Removed hose clamps on drain to DM and garbage disposal. Replaced hose and tightened clamps. Checked for leaks. Buttoned up faceplate on bottom of DM.
Removed hose clamps on drain to DM and garbage disposal. Replaced hose and tightened clamps. Checked for leaks. Buttoned up faceplate on bottom of DM.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Coos Bay, OR
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We needed a new bottom dishrack the old one was very rusty
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Erving, MA
- Parts Used:
- 674744
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Door comes down to fast, Broken Door Assist Spring
Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Greene, ME
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Installed wheel assemblies to rack
Assemblies snap on, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip D from Auburn, AL
- Parts Used:
- 4387043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karolyn from Wellington, FL
- Parts Used:
- WP304170
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Super Fast Shipping
The part arrived the next day with regular postage, outstanding service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emerson from Denver, CO
- Parts Used:
- 675806
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Wrench (Adjustable)
the center screw in the impeller was too thigh, and the adjustable wrench wont hold the impeller still
I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.
Was this instruction helpful to you?
Thank you for voting!