DP920PFGY4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from TUCSON, AZ
- Parts Used:
- WP3367910
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber around the cap assembly was torn
I pulled the basket out, pulled the cap and connector assembly off with ease, no tools needed, it comes right up, and put the new one on. Put the basket back in and it works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Wiggins, MS
- Parts Used:
- WPW10204131
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken trolley axle in rack adjuster
No tools required except possibly a small screwdriver to help remove stop in end of rack; part easily installed by hand and stop re-inserted. Finished in several minutes. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from WHITESBURG, KY
- Parts Used:
- WP3369769
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Remodeling a house and front panel on dishwasher was bent and needed replaced. I just measured panel and ordered without a model or part number. Was so lucky the panel fit perfect.
Just took old panel off and went side to side and then slide panel under front trim. Of course it was easier because the bottom door trim was off and now I have to find that replacement part. Not having any luck with that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Peoria, AZ
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original dishrack had become rusty
installed a new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Union Bridge, MD
- Parts Used:
- WP8268645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheel on lower rack broke.
New one snapped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Roanoke, VA
- Parts Used:
- W11027965
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My original part was broken. Almost unusable.
Replacement part came. It was broken. I took pics of it, and send the pics and an email to PartSelect. They put another replacement part in the mail on the spot. I was shocked! The 2nd one arrived in perfect condition. BONUS POINT to PartsSelect!
Tom Houser
Roanoke, VA
Tom Houser
Roanoke, VA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rochester, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Rack Was Rusting Out
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from St Johnsbury, VT
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower rack started to rust through coating
Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donal from SPRINGVILLE, TN
- Parts Used:
- 4318050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
One door spring broken, replaced both
As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from TEMECULA, CA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
NEW GASKET
I USED A PLUMBER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from ELGIN, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
my old lower dishwasher rack was rusted out and some parts broken.
Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.
ooks beautiful and works perfectly.
Could have used some directions though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!