DU9000XR0 Whirlpool Dishwasher - Instructions

This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!

Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.

Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!

the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack

Unplug Dryer. Remove two screws from front panel of dryer on lower left and right. Dryer front will swing out and up to release the hinges at the top of front panel. Set panel aside to the left and remove wires from switch at inner top left of panel (if necessary). There are 3 thermostats in this dryer. Two are set together at lower left and one is on lower right and sits back a little. This Cycling Thermostat is one of the two (on the lower left) and in my dryer, was the one on the right of these two. Check to make sure the numbers (and wire colors) on the replacement match with the thermostat being replaced, because it could be different from mine (Maytag couldn't tell me the difference). Remove the 3 wires from the thermostat with needle nose pliers and then use a 1/4" deep socket to unscrew the thermostat. Replace in reverse order.

It took longer to take the 2 screws out than it did to put spring on.

installed a new rack

simple, simple, simple ! popped off the old ones, snapped on the new ones. Thanks !

All pieces just snap off and the new one just snap right back in place.

Remeber take a little time to do your repair correctly.

It is cheaper to repair an appliance than it is to replace.

i used a screwdriver to pry off the old wheels then snapped on the new ones.
This was the easiest repair I have ever made on an appliance.

Followed the exellent instructions, the flange kit really solves the problem of lower rack wheel catching on the seal. Superior replacement parts compared to previouse repair two years ago.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

I snapped the old ones off & snapped on the new ones. It couldn't have been easier!

I prayed old wheel assembly’s off with the claw end of a claw hammer. Carefully snapped on the new assembly’s which were a little tricky to align. Went well, took about 15 min.

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.