DUL240XTPB3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jon from Bend, OR
- Parts Used:
- WP8269209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher. Quit mid-cycle.
Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Beaufort, SC
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from FULLERTON, CA
- Parts Used:
- 8193983
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Upper rack not getting clean.
Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Las Vegas, NV
- Parts Used:
- W10301577
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
change front panel
easy as long as you have the right tool to take the panel off, maybe they could include one for people who don't have a good selection of tools. Thankfully we did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from columbus, NE
- Parts Used:
- WPW10757217
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Lebanon, CT
- Parts Used:
- W10518394, WPW10477552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher wouldn't work
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Liisa from Taunton, MA
- Parts Used:
- W11158802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Basket was broken
Sorry -- but my 5 yearold replaced this broken item -- He helped by slipping off the old broken one and sliding in the new one -- No tools were necessary -- after all it was the silverware basket ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conelis from Eclectic, AL
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The motor was too loud
I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eva from Shalimar, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Heater element broken
I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from SARATOGA SPGS, UT
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Roseville, CA
- Parts Used:
- 8193762
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher died
1. Opened inside panel (about 8 screws)
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!
2. Checked wires to see if we had power, which led me to the fuse.
3. All wires were hot, so I bypassed fuse straight to the motor, which worked.
4. Took out the fuse, didn't really know for sure whether it was bad yet, googled the part number and it led me to PartSelect.com!
5. Ordered part (it arrived in two days!) and replaced existing fuse and WE ARE WASHING DISHED AGAIN!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eugene from REVERE, MA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door would fall down when unlatched
Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from ESTES PARK, CO
- Parts Used:
- WP8564547
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The unit had power, but would not start
Removed the front control panel and control unit cover. Removed and disconected old control panel and installed the new panel. Very easy project, even though I didn't know what I was doing. Unfortunately this was not the problem. I had to also replace the heater element and Hi-Temp thermostat. Also easy replacements. The "Just Ask" option is well worth the money. It was a great help in diagnosing the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Daleville, AL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dishwasher would not dry (heat)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.
Nothing to it. I then had to reset the error code and it is working like new.
Was this instruction helpful to you?
Thank you for voting!