DU9700XR8 Whirlpool Dishwasher - Instructions

We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.

I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.

screw it in then hook up the hose.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

Watched your video

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).

Had to clip the part onto the upper rack. It was a little tight at first, then all of a sudden it just snapped in. Voila, as good as new.

Tried using my hands to bend back the locking plastic connectors enough to get them onto the metal upper storage rack;was afraid of breaking the connectors so I used my utility tool needle nose pliers to give me leverage. This time I was successful. Believe me,it was frustrating for what seemed a long time. No,for me it was not easy.