DU925SCGQ1 Whirlpool Dishwasher - Instructions

I removed the screws on the door cover and snapped in the new clip

for the arm I just removed one screw and replaced the arm

Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.

Replaced the middle spray arm kit and the upper spray arm mount. Also replaced worn out spring for the soap dish.
Now all areas of the dishwasher get cleaned and the soap dispenses correctly every time.

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.

I simply unscrewed the remainder of the wash arm retainer nut, removed the wash arm bearing ring and spray arm bearing ring and replaced them; No tools were required. At the same time I decided to replaced the upper wash arm with a kit from Part Select. This did require the use of a philips head screwdriver. The job was real easy and accomplished within 1 hour.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Turned off the power to the Dishwasher. Removed 6 Torx screws holding control panel cover. Disconnected the connectors to the control assembly. Removed and replaced the control board. Replaced the thermal fuse and the door switch. Reconnected the connectors. Reassembled the control panel cover. Turned on power and tested the DW. All OK.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door