DU5000XW0 Whirlpool Dishwasher - Instructions

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)

I USED A PLUMBER

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

Just took old panel off and went side to side and then slide panel under front trim. Of course it was easier because the bottom door trim was off and now I have to find that replacement part. Not having any luck with that!

The brackets that held the original wheels were still on the rack. They were easily pulled off the rack. The new assembly did not look like the original part. It was not difficult to see how they fit onto the rack. The only caution is to press the top part of the new assembly onto the frame before snapping the rest of the new piece into place.

the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack

simple, simple, simple ! popped off the old ones, snapped on the new ones. Thanks !

We read your help site and was able to find what was causing our water filling probelms. Order the valve intake part and made the repair and the dishwasher works like new. You saved us a repair bill from the professionals and they couldn,t done a better job. I will recommand to site to everyone. Thanks Again

One day after placing my order, replacement wheels arrived. I used a screwdriver to pop each (4 total) old set of tandem wheels off the basket basket and poped each new set on.

Removed old wheels, unclipped. Clipped in new wheels.

i used a screwdriver to pry off the old wheels then snapped on the new ones.
This was the easiest repair I have ever made on an appliance.

All pieces just snap off and the new one just snap right back in place.

Remeber take a little time to do your repair correctly.

It is cheaper to repair an appliance than it is to replace.

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.