SUD4000HQ2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roy from matteson, IL
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
leaking
put new seal in and it still leaked!hum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from ickesburg, PA
- Parts Used:
- WP3368999
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Long spring broke that pulls soap cup open
Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.
Was this instruction helpful to you?
Thank you for voting!
Water in bottom of dishwasher
Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Jose, CA
- Parts Used:
- WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leakimg a lot of water from under door.
Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hendersonville, NC
- Parts Used:
- 676413
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dish was broken and needed to be replaced
The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sacramento, CA
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Stopping in the middle of cycle. Finally quit completely.
Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Soldotna, AK
- Parts Used:
- WPW10509257, WP596669
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking during cycle
I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Eight Mile, AL
- Parts Used:
- W10844024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Wouldn't fill with water
Instructions very easy to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Woodstock, IL
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking where motor drive shaft enters pump
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SELKIRK, NY
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad door switch
i took the inside door off and took the 2 switches out and replaced them; not too difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Mt. Carmel, TN
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Roller came apart or broke apart
Take the stop off the end of the roller assembly, remove the old roller and replace with the new roller. Replace the stop assembly. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colorado Springs, CO
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old whirlpool soap dispenser latch wasn't working
Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Charlotte, MI
- Parts Used:
- 4318050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring
The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Rogersville, MO
- Parts Used:
- W10844024
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The old valve has a small leak
Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.
Was this instruction helpful to you?
Thank you for voting!
There were no provided instructions, just had to wing it.
Trial and error. The spring was difficult to install, the pin and door were easy.
Was this instruction helpful to you?
Thank you for voting!