WDTS8024SZ0,WDTS8024SV0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Sterling Heights, MI
- Parts Used:
- W11551775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Warranty Service lost the two screws that held the cover below the door in place
It’s great when you have parts that fit and a schematic to go by. I got both from this site. There are three parts that these screws hold in place. Use the schematic to see which way each part is facing. Line all the parts up and then look through the covers. You’ll see pre drilled holes on either side of the cover. Line the screws up to the pre drilled holes. Put the first screw in half way then insert the second screw all the way. Come back to the first screw and tighten it all the way. Two screws, two minutes and I was done. Real easy repair, just awkward as you are on your belly on the floor. I used a drill with a socket that fit the screw head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerould from East Wenatchee, WA
- Parts Used:
- W11412291
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher would not completely drain e1 f9 error
Pulled the dishwasher out from under counter - removing 2 screws accessible on sides of dishwasher - these screws hold dishwasher under counter. Drain pump accessible right side bottom. Disconnect wiring clip - grab pump turn counter clockwise 1/4 turn and pull out of housing. Then reverse this process for installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Fort Wayne, IN
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack had rusted out
Replaced the old rack with a new one. Saved about $30.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antony from Lakewood Ranch, FL
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dishwasher was not firmly connected to the counter
Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvyn from Mountain Springs, NV
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old dish holders rotted from hard water
replace bottom tray with wheels. I recommend get them with wheels already attached. Very difficult to remove old wheels from rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna K from Alexander, NY
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
prongs were braking off on the rack
took the old rack out and rolled the new one in. Took about 2 mins if at all that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from CHARLOTTESVILLE, VA
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simply replaced lower dish rack in dishwasher.
No explanation is necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Maple Valley, WA
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Under Counter Anti-Tip Brackets Broke
I put this unit in about 3 years ago and the brackets broke at the crease and the dishwasher fell forward. Found the right bracket and when it arrived looked a match. Checked link to video showing how to properly install the brackets. The original manufacturer never stated that the tab that goes through the frame is supposed to be bent 90 degrees to prevent the bracket from coming out. Thank you PartSelect for that video because I would probably end up ordering brackets again in a few years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Croton on Hudson, NY
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher basket broken
We used the rollers and utensil basket from the old basket and in less than 30 minutes the new basket was ready and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Montrose, CO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
I had not needed to install the mounting brackets that came with the dishwasher because the old counter top was 1 inch lower than standard and I was able to just wedge the dishwasher into the space and it would not tip.
I simply disconnected the power line to the dishwasher and pulled it out enough to install the mounting brackets. The installation manual that came with the dishwasher described how to install the brackets and I simply followed directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Naperville, IL
- Parts Used:
- W10728159
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace lower rack
open dishwasher remove lower rack roll in new lower rack
Was this instruction helpful to you?
Thank you for voting!