7DU910PFGB0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Sherwood, OR
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Winnemucca, NV
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from potomac, MD
- Parts Used:
- WP3378138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The soap dispenser lid was broken
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alastair from Atlanta, GA
- Parts Used:
- 3374621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Water inlet valve had frozen and burst
After turning off the water to the dishwasher, I used the adjustable wrench to remove the incoming water line. Then removed the electrical feed to the water valve. Lastly I removed the rubber hose on the outlet of the valve (after compressing the retaining clip) before removing the one screw that held the valve to the lower frame of the dishwasher. Once the new part arrived, it was simply a matter of reversing the above procedure to install the new part. Took under 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sallisaw, OK
- Parts Used:
- WP717273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes would'nt come clean or dry from torn boot
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from encinitas, CA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from KENTS STORE, VA
- Parts Used:
- W10311986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack was deteriorating (extensive rust) and needed to be replaced
The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Coolidge, AZ
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ulysses, KS
- Parts Used:
- WPW10509257
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LEONARDTOWN, MD
- Parts Used:
- WP3379383
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broken door spring
Pulled dishwasher out from counter. Took cover off and replaced door springs.
Was this instruction helpful to you?
Thank you for voting!