DU805DWGQ2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from Keithville, LA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leak in dishwasher
This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)
Was this instruction helpful to you?
Thank you for voting!
My Dishwasher Started Leaking Out The Bottom Of The Impeller Assembly.
I went on line and found the partselect website and was able to identify the defective parts using the schematic drawings. I ordered the parts and in about an hour I had reassembled the dishwasher and had it running again much to the joy of my wife and children. (No more washing dishes by hand!). I also purchased the touch-up paint and tine tips and now the washer looks and runs like it did when I purchased it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from matteson, IL
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
leaking
put new seal in and it still leaked!hum
Was this instruction helpful to you?
Thank you for voting!
Will not dispense soap
Remove old spring pin, spring, door
Waste of time effort and money didn't change a thing still won't dispense soap to wash dishes
Waste of time effort and money didn't change a thing still won't dispense soap to wash dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from ickesburg, PA
- Parts Used:
- WP3368999
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Long spring broke that pulls soap cup open
Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.
Was this instruction helpful to you?
Thank you for voting!
Water in bottom of dishwasher
Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodward, IA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaking in lower front door area
Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Charlotte, MI
- Parts Used:
- 4318050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring
The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jagannathan from Centreville, VA
- Parts Used:
- 3380371
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Wheel
I removed the top dishrack by removing the front clips(stops) on the tracks. Then I removed both tracks by removing the back stops. Then I replaced 7 wheels. Then I replaced the tracks, dishrack and the front stops. The whole job took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Mt. Carmel, TN
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Roller came apart or broke apart
Take the stop off the end of the roller assembly, remove the old roller and replace with the new roller. Replace the stop assembly. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Woodstock, IL
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking where motor drive shaft enters pump
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hendersonville, NC
- Parts Used:
- 676413
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dish was broken and needed to be replaced
The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Soldotna, AK
- Parts Used:
- WPW10509257, WP596669
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking during cycle
I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.
Was this instruction helpful to you?
Thank you for voting!