WDF341PAPM0 Whirlpool Dishwasher - Instructions

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy

followed directions, a kid could have done it,

Remove and replace by hand, no tools required

New one snapped right into place.

I pulled the dishwasher out just over half way to access the spring area. Unscrewed the old assembly and screwed the new one in it's place. Attached the string line to the spring, wrapped it around the assembly and attached it to the door hook. Repeated procedure on other side. Problem solved.

Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.

The door balance springs are connected to the door via a nylon cable which snakes through a couple of pulleys. The plastic fastener on the end of one of these cables separated, so the one remaining spring was not able to offset the weight of the door. Easy to fix, just slide the unit out about 15 inches (remove base plate, and undo a couple screws on top) then replace cables. You can buy just the one cable, or for a couple bucks more, both L&R cables and new pulleys. Replaced the pulleys on my unit at the same time (remove one screw and twist out) since the replacement parts were of better quality than my factory parts. Don’t pay a repair guy $250 or more to fix this for you. It’s easy.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!

Thank you for letting me share my repair experience with you.
I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet.
Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.
Thank you.

Followed the parts list diagram and confirmed with the link on the other side of door. Hooked the plastic attachment to the door, threaded the string around the plastic pulleys, attached the spring and mount it to the back of the dishwasher. that was it! Very easy to do. Hardest part was sliding the dishwasher out and in.