WDT531HAPM0 Whirlpool Dishwasher - Instructions

Total repair time after watching videos was 53 minutes. I estimate I saved between $200 to $300 by doing this myself. If you have any DIY skills, don't hesitate to replace the detergent dispenser yourself.

I manually attached the track stop to the right track in the disheasher.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

followed directions, a kid could have done it,

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.

Pulled dishwasher out unplug the wire on each side unscrew the nut on each side lift up in the back of element pull it out on metal holder for element and put the new one in really easy thanks so much for the help!!

remove the bottom plate with a nut driver and back off on the front leg adjusters. Slide out the dishwasher approx 8-10 inches and remove the broken link. The new one goes on easily. Look at the opposite side if in doubt as to how to attach. Slide the unit back in and tighten the leg adjusters until the unit is secure. reattach the lower front panel which hides the leg adjusters, etc. You're done!

Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

Pretty easy for the parts. Taking the dishwasher out is the hard part. Typically, you should be able to unscrew the 2 screws holding the dishwasher to the underside of the countertop and then slide out the dishwasher to expose the cable assembly - but you also need to unplug the unit (unless it is hardwired), disconnect the hot water supply line from the angle stop (remember to turn off the angle stop) and sometimes disconnect the drain line from the vacuum breaker or garb disposal. You need to disconnect these things so that you can move the dishwasher out far enough to be able to see the entire right and left sides of the dishwasher. Once that hard part is done, you use a hex driver to remove the old cable pulleys, put on the new cable pulleys, and then feed the light weight cable through the pulleys - the end with the big plastic thingie attaches to the door and the other end attaches to the spring. Then you grab the spring and manhandle it onto the back end of the dishwasher chassis (look for the small hole in line with where the cable would line up. Careful as the spring attachment step could result in an injury - Hope this helps.