Models > MDB8969SDE3 > Instructions

MDB8969SDE3 Whirlpool Dishwasher - Instructions

Jump to:

All Instructions for the MDB8969SDE3
76 - 90 of 126
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Terry from Mertens, TX
Parts Used:
W10861000
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dispenser Slide Lid Missing
After Accessing Inner Panel of Door. Opened 8 Small Tang Clips Holding Unit. Cleaned Surface and Straightened Tangs. Popped Unit In Securely & Reassembled. Cleaned Drain Strainer to Load & Wash !
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lana R from THE HILLS, TX
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
The wheel fell from the lower dish rack--the front left hand side.
We snapped the old one off --it did not break. We positioned the new one in the right place making sure that the slot in the middle matched up with the longitudinal wire of the rack and snapped it in place. EASY!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
martin from Ontario, CA
Parts Used:
WPW10348269
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Drain pump had something lodged in it
In all honesty, it took me longer to remove the dishwasher than it did to install the new drain pump.
Pull the plug to kill the power, turn the water supply valve to off and disconnect the water supply hose.
Disconnect the drain hose and drain the water from it into a small tub.
Remove the two "anti-tilt" screws from the top of the D-washer
Remove the two screws holding the "toe kick" plate in place, remove the plate and place of to the side.
If needed, raise the front feet/legs, slide the D-washer out until you can reach the back legs, raise if needed, and side the washer the rest of the way out.
Lay out a towel on the floor, lay the washer on it back. You will see the discharge pump (the one with the big hose coming out of it), remove the hose clamp and hose from the pump.
Disconnect the little power plug from the pump
On the opposite side of the little plug is a gray little plastic tab, squeeze it and rotate the pump counterclockwise about an inch, the pump should fall out in your hand.
Take the new pump, rub a little dish soap (not that crappy hand cleaner stuff) on the rubber gasket and install the new pump making sure the little plug receptacle is facing you and rotate it until it stops, you should hear a small "click"
Now follow all the steps in reverse to put everything back together.
This site has a great, short video that covers everything I have mentioned above.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from WHITEHALL, PA
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Wheels kept coming off.
Took off the broken part replaced it with new part.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Duluth, GA
Parts Used:
WPW10348269
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dishwasher wasn't draining
The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.

I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tasha from ELDON, MO
Parts Used:
W10847918
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The cover to the power box gotosplaced during above and change of power cord
It has brackets that slipped right into the box. The hardest part was reattach the entire box to the side of my dishwasher.
I do feel anyone could do this repair
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lena from Napoleonville, LA
Parts Used:
8269144A
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)
Leak in hose
Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from FRAMINGHAM, MA
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Wheel came off. Hub that held the wheel to the assembly got burned by heater.
Look at the way that 3 remaining Wheel Assemblies were attached to rack, Then pop off the offending assembly and attach the new one. Less than 5 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
G from BISMARCK, ND
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
A wheel on the lower dish rack wheel assembly broke off.
Pry the old wheel assembly and snap the new one in place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from CANTON, MA
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Broken wheel
Easy. Just watched video.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from Drexel Hill, PA
Parts Used:
W11177741
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Original door seal came out while emptying dishwaher. It was pretty messy so i ordered a new one.
I just followed the directions on the video that was part of the pictures for the door seal. I made sure that the channel was clean and the new seal pressed right in. i wish I had checked this site before I called a repairman, who wanted to charge me over $400 for a new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Beaver Falls, PA
Parts Used:
8269144A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Drain pump malfunction/melting
My dishwasher wasn't completing cycles and would start to smell like burning plastic randomly. I determined it wasn't coming from inside the tub but underneath the unit. I replaced the drain pump and the drain hose as a precaution to make sure the check valve inside wasn't getting stuck closed forcing the pump to not be able to drain. It was a very easy repair that just involved taking the dishwasher out of the cabinet and turning it on its side. The old pump just twists out and the new one goes in just as easy no tools required. The video instructions on the product page here were very helpful. The hose connects with a clamp and is routed on the side with some plastic clips. It was very easy and completely solved the problem!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
TRACEY ANN from BRICK, NJ
Parts Used:
WPW10195039
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cameron from DEFIANCE, OH
Parts Used:
W11177741
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Water leaking from out the bottom of door.
Watched the video provided by this site on changing a dishwasher door seal and then replaced my seal as per video. Very simple task. I think the key point of installation is folding the new seal in half to get the midpoint and then inserting that spot first using door latch as midpoint guide and bring the seal around both corners to the bottom. Works perfect.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Troy, MT
Parts Used:
WP8270020
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Replaced door springs and installed cable kit
Viewed the video and, Done!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MDB8969SDE3
76 - 90 of 126