MDB8959SFZ3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from CYPRESS, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The wheels would not roll.
Replaced the wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Highland Village, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Door Leveler Nylon Cord assy broke
It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Santa Clarita, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken cord on door balance
Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.
Thanks,
Ted K.
Thanks,
Ted K.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from TRES PINOS, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Two wheels on the lower rack kept falling off.
Very, Very easy - watched the Installation Video highlighted on web page and the entire process took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from LUMBERTON, TX
- Parts Used:
- WPW10327249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water flow to dishwasher
Removed lower kick panel and there it was on the left hand side. Removed the waterline and removed the mounting screws. Disconnected the inlet waterline into the dishwasher. Removed the bad inlet valve and replaced in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from KENT, OH
- Parts Used:
- W10861000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out detergent dispenser
Total repair time after watching videos was 53 minutes. I estimate I saved between $200 to $300 by doing this myself. If you have any DIY skills, don't hesitate to replace the detergent dispenser yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from CLARKSVILLE, TN
- Parts Used:
- W10919676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
This did not fix the rack issue
It was wrong part. Visual in diagram does not clearly show what needs to be replaced. Old part just broke so we do not know what needs fixing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from MOUNT AIRY, MD
- Parts Used:
- 8194001
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Broken door spring
My husband managed, with some difficulty, to finally replace the broken spring and associated door balance kit. He first ordered the spring from this site. Then, after he had laboriously rolled the dishwasher out about 12" - using flat pieces of wood as support, while he lowered the dishwasher onto his homemade rollers - he realized that the corded door balance kit was also broken. So he rolled the DW back in and ordered the part. This site sent an improved door balance kit, and then he went through the same process again. He had to fish the spring back all the way to the very back of the DW and hook it through a hole, using a rod and masking tape (bad DW design, he says). Then after he rolled it back, he noticed a leak in the incoming hot water connector, at the copper pipe compression fitting. Fortunately, a local plumber, with the right tool and expertise was able to quickly fix that problem. (The plumber explained that compression fittings commonly begin leaking if even slightly moved.) Bottom line: A+ for this site, C for KitchenAid design. He says he'd undertake it again, in spite of the hassle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wheatland, CA
- Parts Used:
- 8194001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Door cord Broke
Hardest part of job was sliding dishwasher out. Put in wood floors so limited free space. Had to lower fron foot pegs first, then remove 2 screws from top that held unit steady. Once dishwasher was out a good 16" cords were easy to replace. Did not replace bracket that came with kit. Cords attach to heavy duty spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Los Angeles, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Door Drops - No Balance
My 2 yr old sat on the dishwasher door while it was open. It snapped both the links on the door causing the dishwasher door to drop every time it was ajar. It was a real danger to the kids or to anyone else unaware of the door given its weight.
I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.
Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system
I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.
Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fritz from AUBURN, WA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The cable, broke that controls the tension on the door
Pulled the dishwasher out and removed the plastic pulley on the bottom of the unit. Installed the new pulley. wrapped the string assy. around the pulley and attached it to the spring and reinstalled it to the back of the dishwasher. We discovered the front bracket on the dishwasher door was bent slightly causing the string to rub and probably is what caused the string to break. We bent the bracket back into shape and reinstalled the dishwasher in its cavity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Stillwater, MN
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Spring broke on door
We pulled the unit out and were able to easily see where it broke. We replaced it relatively easy, pushed dishwasher back in; however, somehow the pump seal got broken in the process so now we have to replace the pump. This was totally unrelated to this repair - only can assume it happened when we pushed the unit back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from NORMAN, OK
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
door balance cord broke
repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.
Was this instruction helpful to you?
Thank you for voting!