JDB8700AWS2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from TRES PINOS, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Two wheels on the lower rack kept falling off.
Very, Very easy - watched the Installation Video highlighted on web page and the entire process took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CANTON, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken wheel
Easy. Just watched video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G from BISMARCK, ND
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A wheel on the lower dish rack wheel assembly broke off.
Pry the old wheel assembly and snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from FRAMINGHAM, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wheel came off. Hub that held the wheel to the assembly got burned by heater.
Look at the way that 3 remaining Wheel Assemblies were attached to rack, Then pop off the offending assembly and attach the new one. Less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Drexel Hill, PA
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door seal came out while emptying dishwaher. It was pretty messy so i ordered a new one.
I just followed the directions on the video that was part of the pictures for the door seal. I made sure that the channel was clean and the new seal pressed right in. i wish I had checked this site before I called a repairman, who wanted to charge me over $400 for a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from COGAN STATION, PA
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door would just fall open
Followed directions here. Extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LONGVIEW, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The dishwasher door wouldn't hold in any position but went all of the way open.
You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIMMY from ST GEORGE ISL, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cord on balance mechanism broke.
pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ELGIN, IL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dishwasher door
Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST NEWFIELD, ME
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
spring cable end broke
followed your very well done video clip exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from Ontario, CA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump had something lodged in it
In all honesty, it took me longer to remove the dishwasher than it did to install the new drain pump.
Pull the plug to kill the power, turn the water supply valve to off and disconnect the water supply hose.
Disconnect the drain hose and drain the water from it into a small tub.
Remove the two "anti-tilt" screws from the top of the D-washer
Remove the two screws holding the "toe kick" plate in place, remove the plate and place of to the side.
If needed, raise the front feet/legs, slide the D-washer out until you can reach the back legs, raise if needed, and side the washer the rest of the way out.
Lay out a towel on the floor, lay the washer on it back. You will see the discharge pump (the one with the big hose coming out of it), remove the hose clamp and hose from the pump.
Disconnect the little power plug from the pump
On the opposite side of the little plug is a gray little plastic tab, squeeze it and rotate the pump counterclockwise about an inch, the pump should fall out in your hand.
Take the new pump, rub a little dish soap (not that crappy hand cleaner stuff) on the rubber gasket and install the new pump making sure the little plug receptacle is facing you and rotate it until it stops, you should hear a small "click"
Now follow all the steps in reverse to put everything back together.
This site has a great, short video that covers everything I have mentioned above.
Pull the plug to kill the power, turn the water supply valve to off and disconnect the water supply hose.
Disconnect the drain hose and drain the water from it into a small tub.
Remove the two "anti-tilt" screws from the top of the D-washer
Remove the two screws holding the "toe kick" plate in place, remove the plate and place of to the side.
If needed, raise the front feet/legs, slide the D-washer out until you can reach the back legs, raise if needed, and side the washer the rest of the way out.
Lay out a towel on the floor, lay the washer on it back. You will see the discharge pump (the one with the big hose coming out of it), remove the hose clamp and hose from the pump.
Disconnect the little power plug from the pump
On the opposite side of the little plug is a gray little plastic tab, squeeze it and rotate the pump counterclockwise about an inch, the pump should fall out in your hand.
Take the new pump, rub a little dish soap (not that crappy hand cleaner stuff) on the rubber gasket and install the new pump making sure the little plug receptacle is facing you and rotate it until it stops, you should hear a small "click"
Now follow all the steps in reverse to put everything back together.
This site has a great, short video that covers everything I have mentioned above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from WHITEHALL, PA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Wheels kept coming off.
Took off the broken part replaced it with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana R from THE HILLS, TX
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The wheel fell from the lower dish rack--the front left hand side.
We snapped the old one off --it did not break. We positioned the new one in the right place making sure that the slot in the middle matched up with the longitudinal wire of the rack and snapped it in place. EASY!
Was this instruction helpful to you?
Thank you for voting!