MDB6949SDM0 Whirlpool Dishwasher - Instructions

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

saw big hole in first (main) hose - got replacement at local hardware thinking it was the only problem - it wasn't - turned on the water and noticed another leak so ordered hose from parts select - fast delivery - installed 2nd hose but still a leak so ordered grommet from parts select - again prompt delivery - installed it and voila no more leak -
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150

Very easy to repair with the replacement wheel assembly. Popped out the broken one, popped in the new one. Price was nothing compared to having an professional repair person come to the home. Glad I found you on line!

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

all 4 wheel units needed to be replaced, popped them off and installed need wheel units in roughly 10 minutes, no tools needed.

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

I was constantly seeing small bits of food blocking the spray holes in the upper and lower wash arms. After a bit of troubleshooting, thanks to the included schematic, the only possible thing left which could introduce particles was the under-unit disposal unit. The dishwasher had to be fully disconnected, removed, and tipped-over to access the pump and motor.

After removing the entire pump and motor assembly, it was obvious what the problem was - the filter screen (which is not accessible normally) was totally destroyed. The motor had ripped the mesh screen up, and sent shards of sharp metal throughout the unit. What a terrible design - a non-user-accessible filter which requires disassembly of the entire product to clean.

I replaced the entire pump and motor assembly which was pretty simple. Just use a very small amount of dish soap to lube the rubber o-ring up to make it slide into place easy. Reconnect all the cables in the same place you removed them from.

If you don't mind using some stainless hose clamps, you could maybe get away with replacing a lesser expensive subassembly - but for me it wasn't worth the hassle.

Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

Pulled the dishwasher out. Cut the power. Tilted over released the wires and motor tabs. Pulled the motor out from the inside of the dishwasher after removing the racks and wash arms.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

Pulled off old seal. Pressed into groove the new door seal. No parts required.

watched video took less than 5 min to replace veeeery easy to do