Models > MDB6949SDH0 > Instructions

MDB6949SDH0 Whirlpool Dishwasher - Instructions

Jump to:

All Instructions for the MDB6949SDH0
31 - 45 of 111
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Derek from ROCKFORD, MI
Parts Used:
WPW10348269
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Dishwasher Not Draining
The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Giorgio from Savannah, GA
Parts Used:
8269144A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
8 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
philip from racine, WI
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
replaced lower rack wheel assembly
watched video took less than 5 min to replace veeeery easy to do
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from NAUGATUCK, CT
Parts Used:
W11177741
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
water leak during wash cycle
I followed the video on the site and it worked perfectly!
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kelly from KINGWOOD, TX
Parts Used:
W11177741
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Slow water drip on bottom side of door, both sides.
Pulled off old seal. Pressed into groove the new door seal. No parts required.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dean from CHAPEL HILL, TN
Parts Used:
W11177741
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Leaking around door
Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lois from HUDSON, NC
Parts Used:
WPW10348269
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from AUBURNDALE, WI
Parts Used:
WPW10195039
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Colin from Goffstown, NH
Parts Used:
WPW10653840
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Door latch wouldn't close
Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Briant from Byron, MN
Parts Used:
4317824
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
13 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from FORT MYERS, FL
Parts Used:
WPW10348269
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Johnny from SUMMERVILLE, GA
Parts Used:
WPW10591570
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Old motor was humming and not pumping the water.
Pulled the dishwasher out. Cut the power. Tilted over released the wires and motor tabs. Pulled the motor out from the inside of the dishwasher after removing the racks and wash arms.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gene from SKYKOMISH, WA
Parts Used:
WPW10348269
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from WASECA, MN
Parts Used:
W11177741
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Door seal leaking because items from silverware basket damaged the seal while sliding the bottom tray back into the dishwasher.
Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from HIGHLAND MLS, NY
Parts Used:
WPW10348269
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dishwasher had a pool of water in it after using it.
Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MDB6949SDH0
31 - 45 of 111