MDB6949SDH0 Whirlpool Dishwasher - Instructions

Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.

All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix.

Easily pulled old gasket from channel. Soaked new gasket in warm water. Cleaned debris from channel with wire brush and CLR. Starting at top-middle, gently pressed new gasket in place. Used a gentle push-pull technique on the corners. Used fingers to smooth gasket all around. Closed door and kept latched for 2 hours. Ran dishwaher to check for leaks.

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.

It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.

Installation was very easy. The online video was excellent and clear.
Thanks

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

Removed bad wheel sets using screw driver to help pry broken part loose. Then just snapped in replacement. Took less than 5 mins. Now it works great.

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

I removed the old gasket. Cleaned the surface under the old gasket and began pressing the new gasket into place. Make sure the gasket is pressed all the way in to properly seat it in the groove. Didn't use the tube of gasket sealer and it worked perfectly no leak,

Was a cinch just watched the video whole procedure took an hr or so

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in