DU4095XX0 Whirlpool Dishwasher - Instructions

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Followed vidio instructionson web site. Quick easy fix

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'