WDF330PAHB3 Whirlpool Dishwasher - Instructions

-Unplugged the dishwasher.
-Removed dish racks, filters and spray arms.
-removed drain pump and drain lines.
-unplugged turbidity sensor and power connectors.
-unlocked the 3 locking connectors, removed the pump and motor assembly.
- cleaned every component with soap and water.
- applied rinse aid to the motor and pump assembly gasket.
-placed pump and motor assembly into the correct position and had a helper hold the assembly down while I locked in the connectors.
-work backwards.

The old filter simply unscrews and the new one screws in.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

Screwed the cap on to the rinse aid receptacle.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

Unplug (disconnect power)
Shut off water
Disconnect water supply line
Clean up any water spills
Remove clips holding air gap hose and wire inside cabinet.
Open dishwasher door and remove two screws that secure dishwasher to cabinet (these are at top of door opening).
With door closed, remove panel under door (this has a screw clamp on each side that requires a quarter turn to release).
Lower the dishwasher as necessary to provide vertical clearance by adjusting leveling legs.
Pull dishwasher out from under counter (grip from under door) far enough to expose springs (one on each side). Take care to feed all connecting lines smoothly through cabinet opening.
Note how existing springs are installed.
Install new spring in the same fashion as the old spring was installed.
Test the door operation.

Push unit back under counter taking care to draw connecting lines back through cabinet opening.
Readjust leveling legs as needed.
Reattach unit to counter top.
Reattach water supply and open valve.
Check for water leaks both at valve and under unit, fix as necessary.
Replace panel under door.
Replace any clips inside cabinet.
Reconnect power

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet