WDF330PAHS4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melissa from JACKSONVILLE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stop broke
Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MCMURRAY, PA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
snap
Just snap it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from hamilton, MI
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
bad heater in qiuet partner 2
this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from The Colony, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heater element snapped in two.
Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACEY ANN from BRICK, NJ
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mount Washington, KY
- Parts Used:
- 8212560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher Loose
Installed brackets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
My dishwasher quietpartner ii was not cleaning my dishes. It seemed it was not heating correctly that the Hi temp wash or the heated dry.
I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Rapid City, SD
- Parts Used:
- 8212560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
With qrantz counter top needed to secure dishwasher to side not top of cabinet opening.
Solution was very simple with the side mounting bracket kit, the only problem was somehow one of the brackets was damaged out of the box . There's a slight off-set on the bracket to allow it to fit properly next to the dishwasher but this one had been flatten out. Had to have happened before going into the shipping box because they were very well protected with bubblewrap. Also, brackets are fairly heavy gage metal so it would have taken some amount of force to do this. Fortunately I was was able to bend it back into a useable shape. It wasn't perfect to look at but because it's mounted behind the side of the dishwasher it didn't matter as long as it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Delaware City, DE
- Parts Used:
- W10445975
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
hose had a hole and leaked
I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Beach, ND
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clean light was flashing and washer would not start
Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antony from Lakewood Ranch, FL
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dishwasher was not firmly connected to the counter
Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Monterey, CA
- Parts Used:
- W11752368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
just wanted to replace the upper dish rack - the pieces have been rusting through
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Centralia, IL
- Parts Used:
- WP8575897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Wheel & Mount Assembly had broken wheel allowing upper dishrack to hang crooked and not pull out properly
Removed plastic end caps from dish rack rail and slid rack off front of rail. Removed rear broken wheel and mount assemble that rail runs on. I believe this took a 3/16" socket which most people would not have and would prevent them from removing this part. With the right tool it was easy, without the tool it would be impossible. Buying tool at local hardware store would be much cheaper than calling repair man. After rear wheel mount assembly was removed, I slid rail forward so I could easily remove the rear rail end cap. I then mounted new wheel mount assemble using original screws and then slid rail through both wheel assemblies and snapped rail rear end cap back into rail. I then slid the upper dish rack on to the rails on both side, slid the wrack back and then snapped the end caps back into the rails fronts on bothe sides. The job was done and the dishwasher was ready for service.
Was this instruction helpful to you?
Thank you for voting!