WDF330PAHS5 Whirlpool Dishwasher - Instructions

The old filter simply unscrews and the new one screws in.

Very easy to twist off the old pump and replace with new part. Worked perfect after replacement! We just followed you tube instructions

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

Open the dishwasher door remove the utensil rack. Next remove all the remaining screws around the outside of the door. Close the door. Slightly lift up on the outside cover of the door, watch out for the wiring inside of the dispenser. Take the flat head micro screwdriver remove the two clips inside the dispenser and then the one main. Next remove the door sensor directly above it just to make the door cover to swing off to the side to make everything easy. Lift up the black flat remove the outside screws with a 6 mm socket push the dispenser back inside the dishwasher. Install and reverse directions don't forget to hook back up the wires.

Just click in, you can basically do it with your eyes closed