DP920PFGQ4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Germanton, NC
- Parts Used:
- WPW10509257, WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish Washer was leaking badly
Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from pine river, MN
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the axels for the wheels of therack adjusters deteriated
replaced the rack adjusters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Oak Harbor, OH
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original faucet adapter for portal dishwasher kept misting water out the sides of the adapter most annoyingly.
So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brendan from SARATOGA SPGS, NY
- Parts Used:
- WP661566
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Montello, WI
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
solution leaking from bottom of door.
first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Watauga, TX
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No water flow to upper wash tray
The cap.nozzle is critical in transferring water to the
upper wash tray in the "heavy wash" cycle only. If this part is defective, simply unscrew it by hand and install the new one by hand in seconds. This
part is inactive in the "light wash" cycle.
Look for deteriation in the black rubber area of the
cap. nozzle.
Ordering and tracking the shipment was a breeze,
everything was very easy to do !!!!
upper wash tray in the "heavy wash" cycle only. If this part is defective, simply unscrew it by hand and install the new one by hand in seconds. This
part is inactive in the "light wash" cycle.
Look for deteriation in the black rubber area of the
cap. nozzle.
Ordering and tracking the shipment was a breeze,
everything was very easy to do !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from cambridge, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher was overflowing
actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher made a crunching, grinding sound and then stopped working.
I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Memphis, TN
- Parts Used:
- 4318273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher wouldn't run
Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley R from Pineola, NC
- Parts Used:
- WPW10273574, WPW10509257
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Water intake hose leaked between plastic/hose connection (metal crimped clamp)
Since I had never made a repair on this 14 year old Kitchen Aid dishwasher, it was "discover as you go." First turned it on its back, took off bottom, disconnected both hoses and found out that hoses would not move. So, had to take off top and remove the back/side unit to get to hoses on top side where they were fastened by tape and a hose holder. Replaced hoses, used old clamp and "buttoned" it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Pomona Park, FL
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my wheels to the top rack broke.
when my package arived , I open the box and pop on my wheels, and all fixed in 60 sec. Thanks you saved me about 650.00 for a new Dishwasher. Thanks Melissa
Was this instruction helpful to you?
Thank you for voting!
the pin was broken
but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Schenectady, NY
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack rusting
This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Milford, NH
- Parts Used:
- W10851031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
clips had broken on the support Support Arm
I used a pair of needle nose pliers to remove the
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Was this instruction helpful to you?
Thank you for voting!
Inserting Lid Spring
Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.
Was this instruction helpful to you?
Thank you for voting!