61-1073-10-00 Tappan Dishwasher - Instructions

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.

I removed two screws that hold unit to countertop,
just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.

The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.

Removed lower panel; unmounted fill valve assembly. Installed two springs. Remounted fill valve assembly and reinstaslled the lower panel. Door must be in a near closed position to gain access to the door "L" spring brackets.

Simply remove the bottom panel below the door. The owners manual (22 year old model) showed the proper hole in which to attach the spring. Attach spring to door and then to frame of dishwasher, as illustrated in manual. It is a tight fit to get your hands in there, but once you do it is a snap. We have replace these springs several times over the life of this appliance, this is the first time we have actually found the proper springs, should last a long time. Thank you Parts Select for having the inventory for such an old model!

This dishwasher has a plastic bolt that holds the actuator on. The action loosens the bolt and it wobbles and eventually comes off. After enough attempts the bolt will strip and need to be replaced. I took some 3M loctite this time to hold it in place. It is 24 years old, but still kicking

I only had one break, but bought both to replace. I don't agree with those that say you have to slide the dishwasher out to repair. I simply removed the lower kick plate, and replace the springs in no time. Very easy as was ordering the parts. I will return here for all my appliance parts in the future. Hope I don't actually need any.

Removed old gasket and clean surfaces on tub and door before installing new gasket. New gasket has a small notch in the middle for top center. Install top then down sides for best results. Door gasket snaps into existing groove so no tools are required.

Took out the old and installed the new and ran the dishwasher, no leak. Problem solved

Ordered the new roller assembly and in no time the upper rack was back together, up and running. Now to see about replacing the other two rollers and the side rails as they are showing wear and tear.

Thanks for the quick ship.

power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.