RUD3000HB1 Roper Dishwasher - Instructions

After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.

The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.

I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!

Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.

Swapped out the old upper dish rack with a new one. A video made the change simple.

Just popped off the old ones and popped on the new ones. Only thing thiat might have been helpful would have been a diagram of where the roller assemblies should be located.

The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

Snapped them in place....2 minutes....ordered the parts 2PM on a friday and they arrived 11AM Saturday...couldn't believe it! Thanks!

Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on

Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!