RUD3000DB2 Roper Dishwasher - Instructions

The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

Instructions very easy to follow

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

we followed your instructions submitted via e-mail and they worked out just fine....thank you

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.

Trial and error. The spring was difficult to install, the pin and door were easy.

I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Replaced front cover. result, bright, clean dished.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!