WU5755B1 Roper Dishwasher - Instructions

i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Replaced the impeller using the kit. Had to brake the impeller since it was stocked due to rust.

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.

turn off power to unit
open the front to remove washer arm and nut
turn unit on its front
looseing the pump assembly from connections
and motor
replaced parts reversed order of assembly
done
cost was much cheaper than other places
one place wanted $160.00 another
place wanted $130.00
with your parts i fixed it for $61.00 that included two day shipping
thanks i will shop here again

after removeing the mounting and trim screws,water lines and associated wiring, the unit slide easily from under the counter then the fun began.
After several years of being exposed to the terrible water here the parts had become covered in lyme scale.
to make a long story short, most of the parts came out with minor difficulty however the pump motor shaft had corroded and lodged into the pump impellar.
This made removal of the pump motor impossible with out cutting off the end of the impellar and driving the pump motor shaft out.
This is NOT something you want to do.
It seems the engineer who designed the pump motor had it's casing made of plastic.
Driving the pump motor shaft out of the impellar caused the back of the motor houseing to break thus rendering the pump motor useless.
Lesson: If it becomes necessary to cut off the impellar of in the pump housing you must completely split the impellar in two parts.
This I repeat is NOT something you want to do.
I recommend replaceing both motor and pump assembly as a unit.

The pump drain hose had been eaten by a rat searching for bits of food. Hose was easy to replace. Then after the repair, we ran the dish washer through its cycles and thennoticed water leaking from under the cabinet from the sink-side. The rat had also chewed the hose connecting the pump drain hose to the sink. Fortunately our hardware store had that hose and we could access that hole from the sink side.

We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.