NDU5J Norge Dishwasher - Instructions

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

Removed old gasket and simply replaced it with the new one. Very easy.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

Removed door interior, confirmed with tester that power was reaching door cut-off switch, but not power on other side of switch when engaged. Noticed that little switch button frozen in shut position, assumed switch had burned out. Installer new door cut-off switch with new (dual) switch units in place, plugged in unit and it ran perfectly.

Removed the inside door panel. Removed the 2 mounting screws to release the latch retainer assembly. Used needle nose pliers to squeeze the posts to release the rinse aid actuator. THIS was the most difficult part since they are made of plastic (didn't want to break it). Removed the spring. Mine did not have a "pivot" to remove since it was a older model, but this would be removed next. Removed old gasket around soap door latch. Pulled tabs hugging the square wax motor actuator and remove. Removed the clear plastic slider. Pulled out the old door latch. Reversed process to put back together. Make sure the gasket around the door latch is pushed all the way down onto the slot of the latch. As a precaution, I also replaced the reservoir O-ring for the rinse aid tank which was quite worn as well. When it's all apart take the cap off the rinse aid reservoir and the reservoir container drops out super easy. That is where the O-ring is. Very glad they had the parts I needed!!

Remove the motor and impeller housing assembly from the unit by disconnecting the motor wiring plug, green ground wire, removing the drain and transfer hose, wash arm assembly and three screws for the filter assembly. A plastic locking ring secures the housing assembly into the unit and is removed by rotating aft about an eighth turn. The impeller is removed from the motor shaft by unscrewing the left hand threads on the fan that attaches to the end of the impeller. The impeller has longitudinal splines that engage the motor shaft, so it has to be removed by pulling straight off of the motor shaft. My impeller was stuck on the motor shaft, so I used a dremel tool with a cut off wheel and sliced through the impeller to loosen it. Installed a new motor shaft oring, and then slid the new integrated seal/impeller onto the motor shaft and secured with the fan (remember left hand threads). Reassembled unit and no leaks...

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

Pulled out the old gasket and pressed in the new one. No more leakage.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.