MDB8969SDH1 Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from SUMMERVILLE, GA
- Parts Used:
- WPW10591570
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Old motor was humming and not pumping the water.
Pulled the dishwasher out. Cut the power. Tilted over released the wires and motor tabs. Pulled the motor out from the inside of the dishwasher after removing the racks and wash arms.
Was this instruction helpful to you?
Thank you for voting!
The little ball bearings were droping into the bottom of the diswasher from the tracks.
I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MIDLAND, MI
- Parts Used:
- WPW10546503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Adjuster tabs broke on both sides
Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).
Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.
As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.
When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.
Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.
As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.
When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HGHLNDS RANCH, CO
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher door leaking
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.
Order both this seal and the seal for the bottom of the door at the same time.
Order both this seal and the seal for the bottom of the door at the same time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from SKYKOMISH, WA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from VESTAVIA, AL
- Parts Used:
- W11259785
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
Left side dishrack track broke. Wanted to install new one.
Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Seattle, WA
- Parts Used:
- 8194001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher door falls when opened
First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from WASECA, MN
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door seal leaking because items from silverware basket damaged the seal while sliding the bottom tray back into the dishwasher.
Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from NEW HOPE, PA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from SAN TAN VLY, AZ
- Parts Used:
- W10195416
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack's wheels broke, all 4 pairs
With a little pressure, I was able to push off the broken wheel pieces with my thumbs. I was able to snap on the new wheel pieces really easily.
This job took less than 15 minutes to replace all 4 wheel pieces.
This job took less than 15 minutes to replace all 4 wheel pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from MODESTO, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wheel assembly broke
I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ELMONT, NY
- Parts Used:
- W11205078, WPW10571946
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishes and glasses were left with residue after cleaning cycle was completed.
There was a small tear in the mesh in the accumulator as well as a noticeable buildup of Detritus in the spray arm. I was able to remove the defective parts and install the new items easily. Total time was less than 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl von der from HUNTINGTN BCH, CA
- Parts Used:
- W10728160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine Row Rusted
At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from ROTONDA WEST, FL
- Parts Used:
- WPW10503549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Was this instruction helpful to you?
Thank you for voting!