DWU7560AAB Maytag Dishwasher - Instructions

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

We had tried to use dish washer cleaners, and they would work for a time, but we started spending more money on cleaner than we wanted. I ordered and then I replaced the lower spray arm. It took a little effort to get the top screw off, due to hard water deposits. The new one went on very easily, just screwed right in like the old one. It's working great and I really don't mind not getting a new one or paying for a service call!!!

My husband does all the repair work himself so he tore it all apart but it's hard to find parts for a 23 year old machine. A store about an hour from our house said they had the part. When we got there it was the wrong impeller and it was going to be $30 to order it in. I got home on that Weds. nite ordered it and had the part 2 days later on that Friday.My husband had the part in and the dishwasher running within 20 minutes. Thrilled with the fast service from you and my husband :)

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Simply had to replace the clips in the correct position. Would have been a five minute job if I had noticed which way around the old parts went before removing them from the dishwasher to find replacements. It's amazing hoe many permutations there were before it all fit together perfectly.

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.

Repair was really quick and simple. Found the part online easily with the information on the website I was confident it would be the right part. Recieved the part in 2 days and snapped it into place. Very satisified!

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

My husband thinks I'm the smartest wife ever! He's telling all his friends how I got online to research the problem (thanks to your readers and DIY comments!), diagnosed it, ordered the parts and - voila - clean dishes once again! It's like everyone said, remove inside of the door by removing 7 torx screws, dismantle wiring -remember to note what connects to what - pop out old parts, easily insert new ones (that arrived in record time!), reconnect wiring, replace door and you're done. Replacing the reservoir o-ring also stopped the leaking problem that preceded the door issue. Thanks PartSelect!

Removed old gasket and simply replaced it with the new one. Very easy.

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~

Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!