MDB6759AWB3 Maytag Dishwasher - Instructions

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

After only 2 years, the Amana dishwasher door began to stick severely. If finally stuck so bad that I had to break the handle to get the door open. The replacement latch and handle fit perfectly and it only took a few minutes to get the screws off of the inner door panel to access the broken latch.

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

I took out the racks and disassembled the bottom assembly until I got to the impeller. Just replaced the part and reassembled. I used only a star shaped driver on all tightened pieces. It was very easy to do and I did not even need any advice/help from the hubby! Saved a whole lot of time and money doing this small repair myself. Thanks for fast service. I ordered part online Thur. late afternoon, and it arrived Friday.

I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!

The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.

The arm has a small bracket that can snap off and on the main water tube easily without tools.

Changing it was a snap!

take handle off old basket put on new basket done

The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.

Having utensils falling through was really getting old. This was $25 well spent.

Removed the handle from the old basket and put it onto the new basket. The new basket is great!

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

In order to clean the screen I had to remove the impeller. Removal required using a wheel puller. I backed off on the impeller screw but left it attached so that the wheel puller could pry against it. I then tightened the puller enough to free the impeller. I was then able to unscrew and remove the screen for cleaning.

I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.

This site has a great video on how to do this. Just follow that.

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.