MDBTT60AWQ3 Maytag Dishwasher - Instructions

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

Used torx bit to remove screws on door and removed the back of door. Removed wiring from switches (2) on broken latch and removed latch. Plugged in switches on new latch and placed latch in position. Screwed back of door into place and that was it! Very simple task and new latch looks and feels much more sturdy than old one.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

Turn-off the dishwasher power at the circuit breaker. Open the dishwasher door flat. Remove the 11 screws around the perimeter of the door using a t-20 torx bit (available at any hardware store). The latch assembly is held on by the top middle two door screws. Pull latch assembly out from top of door. Remove the black and white cable assembly connectors from the latch assembly making sure to note which side each color is on. If you have trouble sliding the connector off, use a flat screwdriver carefully to pry it, but do not pull on the wires. Install cable connectors onto new latch assembly making making sure the black and white cables are on the correct sides. Position the door at a 45 degree angle and place the latch assembly into position while putting the white inner door over it. Reinstall the 11 torx screws around the side of the door being sure the screws are snug, but not overtightened. Test the operation of your dishwasher. The new latch assembly seems to be built better than the factory original.

Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts

I had to replace the touch pad. Called a service guy. He wanted $350 to fix it. Told him to take a hike. Ordered the front touch pad with ribbon cable. Had to remove about a dozen screws around the door, then 3 screws on the control panel inside. Connector for the ribbon cable was pulled back and the ribbon came right out. 4 more screws held the touch panel to the door. Removed those with drill driver. Put new part in and worked fine.

1. Fully opened door of dishwasher.
2. With star driver, removed 11 screws from the insde edge of door.
3. Outside front panel of door then is separated from inside panel slightly to again access to, latch assembly.
4. Verified that replacement part matched existing part.
5. Lifted out damaged latch assembly and disconnected the two electrical leads by gently pulling on the insulated connectors.
6. Connected the electrical leads to the coresponding connections on the new part and replaced in the reverse order of above.
7. Total time for repair was 15 minutes.

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

Remove the 4 screws at the lower panel, turn power off to dishwasher, remove single 1/4 attaching screw from float switch, open the door remove the old float assembly. Make sure you install the float in the machine first than side the switch over the end of the float before screwing it back in.

First shut circuit breaker to dishwasher and close water valve under the sink. Remove the screws that hold the dishwasher to the counter, then remove the bottom cover plates. I slid the diswasher out almost all the way...On the left side bottom I could see the old water inlet valve was attached by 2 hex screws and a clip with 3 wires..after removing the 2 screws and clip I was able to remove the water line (place something to catch a small amount of water) and remove the black rubber hose from the old intake valve by squeezing the clip.. Removed the brass nut from the old valve you'll need it. I installed the new water inlet valve by connecting the old brass nut
(replace with new thread seal tape) , replace the water line and black rubber hose...attach to frame with the 2 hex screws and replace clip with wires...I slid the dishwasher back under the counter, turned the water on and power back on...I ran the dishwasher before I secured it in place to check for leaks...Dry as a bone...I then secured it to the counter and replaced the bottom plates.. the dishwasher is working like new...everything comes out spotless...Sometimes repairs are not as hard as they look, just take your time.

First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Best part, i go this thing on my hands right of way..Great place, great price...Highly recommende