MCD4100AWX Maytag Dishwasher - Instructions

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

Removed 7 Torx Screws ... removed inner door panel ... snapped off the selinoid after noting the exact original position ... removed the Latch assembly 2 hex head screws ... removed the old Grommet which was crumbling apart ... stretched the new grommet in place. Then did the steps in reverse to complete a successful repair.
Thanks to your website, quick turn-around service and customer's repair stories, I probably saved a few dollars but mostly, I realized how much I love my dishwasher now more than ever!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

My husband does all the repair work himself so he tore it all apart but it's hard to find parts for a 23 year old machine. A store about an hour from our house said they had the part. When we got there it was the wrong impeller and it was going to be $30 to order it in. I got home on that Weds. nite ordered it and had the part 2 days later on that Friday.My husband had the part in and the dishwasher running within 20 minutes. Thrilled with the fast service from you and my husband :)

I removed the screws holding on the interior door panel. This exposed the soap dispenser latch mechanism. After removing the two retaining screws I transferred the original parts to the new retainer and replaced the grommet prior to reinstallation of the mechanism and interior door panel. A savings of probably $100.00 or more for a service call and parts. Should last a few more years.

i removed the bottom spindle inside of the washer compartment. laid the pieces out in order of which they were removed. found the impeller was busted where it attaches to the shaft of the motor. screw was missing but found it laying in the bottom (there is a screen that filters the water as it drains). replaced impeller and put parts back together in order. good as new.

Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.

This was the third appliance I have repaired with the help of Parts Select in the last three months.

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.