MDBH980AWS0 Maytag Dishwasher - Instructions

Who ever assembled the parts for shipment, put the latch on backwards and it was extremely hard to take the latch off of the main part. Now matter how hard I tried, I was unable to re-attach the latch until I used a file on the plastic insert to file off the inside edges until they fit. It does work now, but it could have been made much easier if they had simply positioned the latch in the correct position in the first place.

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

remove 11 screws, remove old latch after disconnecting electrical wires, connect wires to new latch assembly, and replace 11 door screws. Easy breezy.

Remove all interior door panel screws with a torx head screwdriver (drill). Pull the interior panel up from the door far enough to access the switch assembly. Pull it out and remove the 2 electrical connectors from the old switch (using a small screw driver as a pry bar if needed). Remove the old switch and handle (that may be broken off and still in the door). Push the electrical connectors onto the new switch assembly, making sure the handle is down toward the opening and the connectors are on the same side as they came off of the old switch. Align the mounting screw holes of the switch with the threaded holes on either side of the switch. Push the interior panel back together and align the two holes with the switch holes (those 2 screws go through the door panel and the switch assembly). Replace the remaining interior panel screws. Done!

Unscrewed dishwasher from counter and pulled it out from under the counter a few inches. Looked at the side of the dishwasher with the remaining good spring and saw how it was attached: One end was hooked to a little tether strung around a pulley, the other to one of a few steel slots. Copied that side for the new spring and works fine now.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.