MDBH968AWB3 Maytag Dishwasher - Instructions

Pulled out the old one and put in the new one!

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

replaced rack

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

Basket Replacement very simple just remove old and set new basket in place

It has been a while since I replaced the handle so I may miss some steps but it was easy to do.

To change the Handle. Turn off the power. Open the front door and undo the torx screws from around the door. Lift up the panel. Remove the broken handle and lugs and insert the new handle.(Their may have been a couple of screws on the latching mechanism that had too be removed to replace the handle)

After replacing the handle the door would open and shut like a new one but the dishwasher still would not turn on. On further inspection I found a fractured joint on a relay on the control board . Resoldered it and it is working great.

The delivery of the part from Parts Select was great,I got the part next day in California.

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

New handle came out of the package and was fully installed in 5 minutes. Couldn't be easier.

remove door panel screws 8 of them.door lock and switch are one unit.pull off wires in order to replace door handle.slip wires back in place and replace door panel.

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.