MDBH965AWB40 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Charlotte, NC
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
external door latch snapped off
1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from green valley, AZ
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
handle did not work properly and unit would not turn off when door was opened
I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronee from Coweta, OK
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic Handle broke (again!)
First I made sure the breaker for the appliance was turned off!
I only had to unscrew all the screws from the inside door.
Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).
Next, I snapped the new Latch Assembly into the two sockets.
Screws were replaced and wa la!
Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.
I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.
Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).
Not bad for a couple of girls!
I only had to unscrew all the screws from the inside door.
Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).
Next, I snapped the new Latch Assembly into the two sockets.
Screws were replaced and wa la!
Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.
I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.
Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).
Not bad for a couple of girls!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Austin, TX
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusting
replaced rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from Reseda, CA
- Parts Used:
- W10283681
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Water not heating
Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer
Elmer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from BOLIVAR, OH
- Parts Used:
- WP99003446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cable broke
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from SANIBEL, FL
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack was rusted in places
Pulled out the old one and put in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burt from LOGAN, UT
- Parts Used:
- WP99003317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace detergent dispenser
I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from DELAWARE, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old silverware basket broke
Basket Replacement very simple just remove old and set new basket in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ORANGE PARK, FL
- Parts Used:
- WP99002598
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Left side door spring broke
It was very easy to replace the broken door spring, I received the new spring from PartsDirect in two days. I removed the 6 screws holding the dishwasher to the counter and pulled it out from the counter about a foot, no need to disconnect the power and water. I simply replaced the broken spring using the right side spring as a guide. I pushed the dishwasher back in and reinstalled the screws. I completed this repair in less than 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mel from PROSPECT, KY
- Parts Used:
- W10280784
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic tongs were decaying in some areas.
No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SPRINGFIELD, VA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking.
Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from St Augustine, FL
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heating Element Corroded
Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dr luther c from state college, PA
- Parts Used:
- WP99002947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Wheel broke on top rack of dishwasher
Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Was this instruction helpful to you?
Thank you for voting!