MDBH955AWB2 Maytag Dishwasher - Instructions

Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of the motor to hold the shaft from moving.

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I bought 2 new new door springs and just replaced both left and right. Just have to pull out the dishwasher about 1/3 to its original position to be able to fully open the door and replace springs located on the side. This model is not complicated . Its very easy to replace parts that are broken. Don't forget to TURN OFF your CIRCUIT BREAKER

Removed screws holding the dishwasher on the side of the cabinet.
Removed the screws from the bottom plate of the dishwasher.
Pulled out the Dishwasher from under the cabinet about 1 foot .
Removed broken Spring from left side of bottom holder making sure not to drop the plastic swivel arm from the bottom metal bracket.
Put the new spring, short loop side end in the plastic swivel arm and expand the long side spring end to the upper bracket holder. Their are 4 different tension slots depending upon how tight you want the front door to open or close. I put the spring on the 2nd slot
Put dishwasher back under the counter, screwed bottom plate & side in.

I removed flowplate assembly, chopper assembly, found that the plastic spindle was stripped causing arm not to spin. In the new seal kit, the spindle was made of metal (much better design). I replaced the spindle, chopper, and filter assembly (old one was caked full of gunk). Worked like a charm. A previous post helped me figure out the problem.

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.