MDBH945AWS0 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elmer from Reseda, CA
- Parts Used:
- W10283681
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Water not heating
Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer
Elmer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from SANIBEL, FL
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack was rusted in places
Pulled out the old one and put in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ORANGE PARK, FL
- Parts Used:
- WP99002598
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Left side door spring broke
It was very easy to replace the broken door spring, I received the new spring from PartsDirect in two days. I removed the 6 screws holding the dishwasher to the counter and pulled it out from the counter about a foot, no need to disconnect the power and water. I simply replaced the broken spring using the right side spring as a guide. I pushed the dishwasher back in and reinstalled the screws. I completed this repair in less than 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mel from PROSPECT, KY
- Parts Used:
- W10280784
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic tongs were decaying in some areas.
No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from BOLIVAR, OH
- Parts Used:
- WP99003446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cable broke
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burt from LOGAN, UT
- Parts Used:
- WP99003317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace detergent dispenser
I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from DELAWARE, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old silverware basket broke
Basket Replacement very simple just remove old and set new basket in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SPRINGFIELD, VA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking.
Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from St Augustine, FL
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heating Element Corroded
Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dr luther c from state college, PA
- Parts Used:
- WP99002947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Wheel broke on top rack of dishwasher
Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Philadelphia, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Latch Asembly Broke, Door wouldn't close properly
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Orlando, FL
- Parts Used:
- WP99002659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wouldn't wash dishes
I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Kansas City, MO
- Parts Used:
- 6-917713
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Latch Assy and Front Panel
Turn off power to the Dishwasher at your breaker panel.
If you haven't done so, turn off the power to the Dishwasher at your breaker panel.
Using a star-shaped screw bit, remove the perimeter screws around the inner edge of the door panel. Remove the screws connecting the control unit to the control panel.
Detach the cables from the latch assembly by pulling the connectors loose.
Detach the ribbon-cable connecting the control panel to he control unit by gently sliding (prying) the connector on the control unit circuit card.
Attach the new Latch Assy to the new Control Panel with a couple screws previously removed.
Attach the ribbon cable of the new control panel to the control unit by just pushing it in and sliding the connector back together.
Attach the cables back to the Latch Assy.
Clean up the edges of the door while easy to get to.
Use a screw driver to push in on the latch assy (where the machine latches to close the door)
Put the door back in place and replace all the screws.
Close the door and turn on the breaker in your breaker panel.
Try out the dishwasher.
VWHALLA!
If you haven't done so, turn off the power to the Dishwasher at your breaker panel.
Using a star-shaped screw bit, remove the perimeter screws around the inner edge of the door panel. Remove the screws connecting the control unit to the control panel.
Detach the cables from the latch assembly by pulling the connectors loose.
Detach the ribbon-cable connecting the control panel to he control unit by gently sliding (prying) the connector on the control unit circuit card.
Attach the new Latch Assy to the new Control Panel with a couple screws previously removed.
Attach the ribbon cable of the new control panel to the control unit by just pushing it in and sliding the connector back together.
Attach the cables back to the Latch Assy.
Clean up the edges of the door while easy to get to.
Use a screw driver to push in on the latch assy (where the machine latches to close the door)
Put the door back in place and replace all the screws.
Close the door and turn on the breaker in your breaker panel.
Try out the dishwasher.
VWHALLA!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Palm Springs, CA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom of utensil basket broke away
Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!
By the way, my order arrived in one day.
Phenomenal!
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!
By the way, my order arrived in one day.
Phenomenal!
Was this instruction helpful to you?
Thank you for voting!