MDB8959SFH0 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- philip from racine, WI
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced lower rack wheel assembly
watched video took less than 5 min to replace veeeery easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from CHAPEL HILL, TN
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leaking around door
Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from LIBERTY TWP, OH
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Rack Wheel Assembly
Installation was very easy. The online video was excellent and clear.
Thanks
Thanks
Was this instruction helpful to you?
Thank you for voting!
The little ball bearings were droping into the bottom of the diswasher from the tracks.
I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.
Was this instruction helpful to you?
Thank you for voting!
Door just fell down
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
Was this instruction helpful to you?
Thank you for voting!
The right top side rack can apart. Wasn't able to reassemble.
I turned off the power to dishwasher first. Removed bottom plate to get to leveling legs. Lowered the legs as to be able to pull and skid dishwasher out from under counter.
Once dishwasher is removed from under locate the 4 screws on right side that hold racks remove them.
I would recommend replacing both skids on both side while you have the dishwasher pulled out.
Very easy to replace new rack slid once old rack removed.
The rack come assembled with skid and plastic holders.
This repair is a 10 minute repair per side.
Thanks Bob Seese
Once dishwasher is removed from under locate the 4 screws on right side that hold racks remove them.
I would recommend replacing both skids on both side while you have the dishwasher pulled out.
Very easy to replace new rack slid once old rack removed.
The rack come assembled with skid and plastic holders.
This repair is a 10 minute repair per side.
Thanks Bob Seese
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUBURNDALE, WI
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from MODESTO, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wheel assembly broke
I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Seattle, WA
- Parts Used:
- 8194001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher door falls when opened
First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giorgio from Savannah, GA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from ROTONDA WEST, FL
- Parts Used:
- WPW10503549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ELMONT, NY
- Parts Used:
- W11205078, WPW10571946
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishes and glasses were left with residue after cleaning cycle was completed.
There was a small tear in the mesh in the accumulator as well as a noticeable buildup of Detritus in the spray arm. I was able to remove the defective parts and install the new items easily. Total time was less than 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from KINGWOOD, TX
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Slow water drip on bottom side of door, both sides.
Pulled off old seal. Pressed into groove the new door seal. No parts required.
Was this instruction helpful to you?
Thank you for voting!