MDB8951BWS0 Maytag Dishwasher - Instructions

I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag for you.

Simple. Unscrew the old one, replace with the new one.
The best part- Online said it would take 5-7 days to recieve thru the mail. It arrived the very next day!!!!

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Basically took out of box and put in dishwasher.

Very simple! First, free the wheel from the rail - should come right out if the wheel is broken. Then click the wheel base off the small shelf rod by rotating the wheel bse. Then, click the rail end cap off the rail by pressing it through the small square hole in the flat side of the rail. Insert the wheel into the rail, then click the wheel base back onto the shelf rail rod where you took the old one off. Click the rail end cap back on, and you're done!

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

Initially ordered the rack adjuster assembly, not realizing that I would also need the adjuster lever and adjuster cover, too. This piece is NOT what originally came with our unit. The line drawing for part 17 shows what our unit looks like. That part has apparently been discontinued and we were guided by Maytag to order this substitution, which is actually a Whirlpool part. Thought someone else might want to know this if they happen to have the same series of Maytag DW as we do. It fits well onto the rack, however, the location of the wheels on the unit are different than the original which means that the middle rack now slides out of the dishwasher about 3" less than it used to, which is kind of a bummer. All that said, the repair was a piece of cake and the hubs on the wheels are now metal instead of the original plastic. . .I expect this part to last a good long while!

I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers