MDB8851AWS1 Maytag Dishwasher - Instructions

Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

the new dishrack fit right in immediately with no tools needed. Delivery was prompt

Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

Pulled the dishwasher out. Determined that it was leaking from the air/water inlet. Ordered the seal and replaced the seal by turning the inside cover counter clockwise while holding the outer water inlet. Replaced seal and installed water hose. Put dishwasher back inside cabinet and leveled. If you don't try to fix it yourself, It could cost more then what it is worth.

took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

After receiving the seal, I installed it and carefully observed its operation and found the reason why the original one was broken in the first place. For some reason the bottom of the washer where it mates with the seal was deformed and it caused the original seal to suffer stress which led to its being broken, and it may be the reason why I got occasional leakage.

We bought this dishwasher at a %40 discount at a Sears outlet. It was probably returned by the original owner for this reason. Using a rubber mallet I was able to easily beat it back into shape and the new seal now fits like a glove.

But probably the most amazing thing was I was able to easily find the part at PartSelect.com after some googling around. Now I know where to find parts for my dishwasher and perhaps other appliances when the need arises.

The first thing I did was read the all of repair stories that others had submitted. Then I set the timer and chucked up the Torx bit in my electric drill/screwdriver. There are 10 Torx screws on the inside of the dishwasher door and they came out very quickly. The top two screws hold the latch in place. I lifted the inside stainless steel cover to get acces to the latch. There was enough slack in the wire that I was able to remove the latch from where it was and extend it above the door. This let me lay the stainless steel liner back onto the inside of the door without removing or disconnecting the soap dispenser. Thus exposed, disconnecting the connectors from the old latch and reconnecting them to the microswitches on the new latch was a breeze. Once connected, I reinstalled the latch assembly, repositioned the liner correctly and replaced the ten screws. The entire job, including putting my tools away and cleaning up took eight minutes. I did it on my lunch break. The eight minutes included pulling the circuit breaker and reconnecting it (very important, that step). The new latch/handle assembly completely fixed the problem.

I did not know exactly which part was causing the leak so I order all the parts to do the job complete.The repair went very well and was very easy to fix. This is after I had 3 other repair men come and try to fix the leak. They said they could not find the problem of the leak and said we were using to much soap. When I pulled out the unit and started it up you could clearly see the water leaking from the air inlet seal. I was very happy with Parts Select my parts were shipped the same day as my order and I received them the very next day. They saved me from having to clean dishes by hand for Christmas Thank You Parts Select.

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

I was able to remove the old handle and place it on the new basket - using only a screw driver.

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.