MDB7851AWB41 Maytag Dishwasher - Instructions

seeing as how my husband was out of town, I inserted a regular flatware knife in each of the four slots that held the handle in place on the basket. I then slowly pushed down on the handles of the knives on opposite sides of each other to unlock the handle from two slots on the basket and then went on to push down on the other two flatware knives on the opposite sides...sure enough, the handle came right off...less than 5 minutes in all to take the old handle off from the old basket and then snap it into place onto my newly acquired basket.

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

Replacement basket did not include handle so needed to pry old handle off broken unit to use on the new one. Used screw driver to pop loose clips which attached to basket. Had to stick tooth picks broken in half under them to hold out until all four clips were opened at once - then handle could be pulled off. Easily snapped it back on to the new basket and repair was done. Can't get any easier than this!

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).

Ordered silverware basket, placed into the proper position. Easy as pie.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

Taking the upper and middle dish racks out, I reached in and pulled out the old parts, then popped the new ones on.
All of the ususal tips for our problem weren't cutting it, so we finally figured the seals at the back of the dishwasher were not effective in keeping the appropriate amount of water pressure in the spray arms. The rubbery seals had been degraded by harsh detergents. We ordered the new seals from your company after a phone call to verify we were choosing the correct parts and easily put them in place. Now our dishwasher does what it was designed to do! And less than $40.00 including shipping! We did not need a new dishwasher.

Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.

The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.

Having utensils falling through was really getting old. This was $25 well spent.

Removed the handle from the old basket and put it onto the new basket. The new basket is great!

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.