MDB7851AWB41 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kirk from tuscumbia, AL
- Parts Used:
- WP99003147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken track whell on upper rack
Very easy to replace the roller. First I removed the stop on the top slide. Then I unsnapped the old roller. The new roller just snapped right in place. Then I put the drawer slide back on.... Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Lansing, MI
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
the dishwaster was not getting the dishes clean
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from SAN FRANCISCO, CA
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Soap not dispensing
I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST NEWTON, PA
- Parts Used:
- WP99003446
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher door would fall open
I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Longmont, CO
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dispenser door broke
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mapleton, UT
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher got the dishes dirty not clean
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fayetteville, GA
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper wash arm would not turn.
Snapped the old part out and snapped the new part in.
It was a piece of cake.
It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lake Zurich, IL
- Parts Used:
- WPW10192799
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishes not clean
with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from Wilmington, DE
- Parts Used:
- WP6-918873
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
bottom of silverware basket broke
received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Reno, NV
- Parts Used:
- 6-917696
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Redeco kitchen black to stainless
1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Wheaton, IL
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack had rust spots.
You just remove the old unit and set in the new unit. the wheels were already connected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from BOLIVAR, OH
- Parts Used:
- WP99003446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cable broke
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Charlotte, NC
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
external door latch snapped off
1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from DELAWARE, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old silverware basket broke
Basket Replacement very simple just remove old and set new basket in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from SANDIA PARK, NM
- Parts Used:
- WPW10192799
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Grit on all the dishes, spots on glasses and hard water buildup inside the entire dishwasher
1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order
Was this instruction helpful to you?
Thank you for voting!