MDB7949SDE1 Maytag Dishwasher - Instructions

Replaced door latch

Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy

followed directions, a kid could have done it,

Very, Very easy - watched the Installation Video highlighted on web page and the entire process took less than 5 minutes!

Removed lower kick panel and there it was on the left hand side. Removed the waterline and removed the mounting screws. Disconnected the inlet waterline into the dishwasher. Removed the bad inlet valve and replaced in reverse order.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

I replaced the thermostat (part # PS11750035) along with the heating element (part # PS9494999) and the turbidity sensor (part # PS11757214). I also checked the filter (part # PS11759673) and it was very clean with no holes. The dishwasher still has water and soap suds standing in dishwasher after I ran it through different cycles. Also, when I run the sanitize cycle the sanitize light flashes red at the end. It doesn’t appear to completely filling with water. Also my hot water temperature is 130 degrees after running for 1 minute. I am at a loss! Any suggestions?

Get a piece of stiff wire (medal close hanger) cut a Short piece and take a tool and roll a half circle on each end making the link length you need then attach the lanyard to the spring

repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.

Fairly easy. Undid the two screws on the kick plate. Then used pliers to undo the leveling legs and pulled the dishwasher out from under the cabinet. The dishwasher is hard-wired with extra electric cable. The drainage tube is flexible and there is extra so I did not have to worry about disconnecting anything. I then attached the new door cable link to the spring. Using the Needle-nosed Vise Grips I pulled the cable so I had enough to make the connection on the door piece. Done. Then I put everything back.

Remove two screws then the two toe-panels. Use a flashlight to locate spring and the hole in the metal frame near back of unit about an inch off the floor. Look at opposite side of unit to see how the working link is routed. Place correct end of the link over one end of the spring and wrap a piece of tape around nylon clip and spring end (just to save frustration of having it fall off while you attempt to complete this task). Tie a loop in the end of each end of the piece of string you supplied. Loop one loop around the spring end with the link clip and feed the other end of the strings loop out the front of the dishwasher at the bottom near the lowermost pulley. Reach under the dishwasher and hook the spring to the frame. Keep tension on the string and feed the link cord out the front of the dishwasher near the front bottom near the lowermost pulley. Loop the exposed end of the self-supplied string around the center of the flashlight handle. Have an assistant pull firmly on the flashlight/string stretching the spring (not too much to over-stretch the spring, but give yourself a little slack too). Serpentine the link cord around the two nylon pulleys. Make sure the rope side of the link clip is toward the back of the dishwasher. Place the link nylon clip over the metal door lever and into the appropriate slot. Have your assistant slowly release tension on the spring/string. Reach under the dishwasher and remove the looped string from the spring end and remove the string. Replace the toe-panels. I did the right side this way, the left side is up against a wall and I might have had additional problems, but it is hard to say since I did not replace the left link. I thought this easier than removing the dishwasher, inlet and outlet as I have done that several times and it can be a pain as well. Good luck!

Ordered the part. Called my son who brought over his toolkit. Played him the repair video on my iPad and he replaced both Door Balance Links. Door works great now.

For some reason I wasn't able to pull the dishwasher all the way out. Had my wife with a smaller hands and arms reached in and attached the spring with the link end onto the dishwaster anchor point. I then put on both nylon rollers. The link anchor point and rope went over the upper roller first. I then struggled and managed, with lots of pulling, to get the rope over the lower nylon roller. All went well with reattaching the water and drain lines. Plumbing in tight spaces is made for small people. This old body does not bend like it use too.
.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,

Replaced door balance link kit and door opens easy does not squeak or slam down.